Snapmaker U1 · Black Friday
4 Pika hotends for your U1. $240, extras free.
Pika is a drop-in high-flow hotend for the Snapmaker U1, up to 80 mm³/s. Every bundle fills all 4 toolheads and adds 4 bonus FIN nozzles, 4 silicone boots and a 6 mm nozzle wrench. Pick the one that matches what you print and you're at checkout in one click.
In every bundle
One Pika for each U1 toolhead, plus the extras.

4 × Pika hotend
One for each U1 toolhead, each with a .4 nozzle installed.
$420 if bought separately
4 × bonus FIN nozzle
Matched to your bundle: .6 plated copper, .6 plated hardened steel or .2 hardened steel.
$88 if bought separately
4 × silicone boot
A spare boot for every hotend.
$16 if bought separately
6 mm socket nozzle wrench
Swap nozzles right on the toolhead.
$4 if bought separatelyPick your bundle by what you print
All 4 bundles are $240 and include the same 4 Pikas, 4 boots and wrench. What changes is the nozzle installed on each Pika and the 4 bonus nozzles. Every button goes straight to checkout.
EverydayCopper bundle
Everyday printing and speed: PLA, PETG, ABS, ASA
- .4 plated copper installed on all 4
- 4 × .6 plated copper bonus nozzles
- 4 boots and a 6 mm nozzle wrench
AbrasivesHardened steel bundle
Glass and carbon filled filaments
- .4 hardened steel installed on all 4
- 4 × .6 plated hardened steel bonus nozzles
- 4 boots and a 6 mm nozzle wrench
Fine detailDetail bundle
Everyday filaments, plus a .2 for fine detail
- .4 plated copper installed on all 4
- 4 × .2 hardened steel bonus nozzles
- 4 boots and a 6 mm nozzle wrench
Abrasives + detailDetail steel bundle
Filled filaments, plus a .2 for fine detail
- .4 hardened steel installed on all 4
- 4 × .2 hardened steel bonus nozzles
- 4 boots and a 6 mm nozzle wrench
What each bundle is for
Copper bundle
PLA · PETG · ABS · ASA
Plated copper on everything. Copper moves heat fastest, so this is the speed and everyday pick. Print on the .4s, switch to the .6s when you want big, fast, strong parts.
Hardened steel bundle
PETG-CF · ASA-GF · PA-CF · PPS-CF
Hardened steel on everything. Glass and carbon fibre chew through soft nozzles, steel holds its size. Pick this if you print filled filaments at all.
Detail bundle
Minis · small text · fine features
Plated copper .4s for everyday printing, plus .2 hardened steel nozzles for parts where detail matters more than speed.
Detail steel bundle
Filled filaments + fine detail
Hardened steel .4s for abrasives, plus .2 hardened steel nozzles. The do-everything kit if you run filled filaments and fine detail.
Why Pika
Up to 80 mm³/s
0.6 mm nozzle, ABS at 280 °C. Up to 60 mm³/s with a 0.4.
Any FIN nozzle. Any size.
.1 to 1.0 mm, swapped right on the toolhead with a 6 mm socket. No disassembly or wiring.
Titanium heatbreak and support structure
No bent or snapped hotends.
Built to be serviced
Take it apart, repair it, put it back together.
| Pika bundle | The other guys* | |
|---|---|---|
| Flow | Up to 80 mm³/s | Up to 55 mm³/s |
| Nozzles | .1 to 1.0, change anytime, no disassembly required | 0.4 only, fixed and disposable |
| Abrasives | Hardened steel, tungsten carbide, Diamondback | Not recommended for carbon or glass filled |
| Durability | Titanium heatbreak and support structure, no bent or snapped hotends | No heatbreak supports, easier to bend |
| Service | Take it apart, repair it, put it back together | No disassembly, no service. Replace the whole hotend |
*A popular high-flow hotend sold for the Snapmaker U1, from its product listing, October 2026. Pika: 0.6 mm nozzle, ABS at 280 °C. Your filament and setup may vary.
Why Pika on the U1
Questions
Will it fit my U1?
Yes. Pika for Snapmaker U1 is a drop-in hotend. The heater and thermistor come preinstalled.
How hard is the install?
Drop it in, then hot-tighten each nozzle before your first print: heat above your hottest print temperature (300 °C covers most filaments) and snug it to 2 to 3 Nm with the 6 mm socket. Install the unload macro too. Step by step: Pika install notes.
How much faster is it?
Up to 80 mm³/s with a 0.6 mm nozzle (ABS at 280 °C), 2 to 3 times stock Snapmaker flow. Up to 60 mm³/s with a 0.4.
Can I change nozzles later?
Yes. Pika takes any FIN nozzle, any size, and you swap it right on the toolhead with a 6 mm socket. The wrench is in every bundle. No disassembly, no wiring.
Which bundle should I get?
If you never print fibre filled filament, get the copper bundle. If you print any glass or carbon filled filament, get the hardened steel bundle. Add the detail version of either if you want .2 nozzles for small parts.
When does the sale end?
11:59 pm Central, Monday, November 30. Sale prices don't apply to orders placed before the sale.
Pick yours. Check out in one click.
Every bundle: 4 Pika hotends, 4 bonus FIN nozzles, 4 boots and a 6 mm nozzle wrench. Ends 11:59 pm Central, Monday, November 30.

